LED調光器 have revolutionized the way we control lighting in various settings, from homes and offices to commercial and industrial spaces. They offer the flexibility to adjust the brightness level of LED lights, thereby enhancing the ambiance, improving energy efficiency, and even contributing to well-being. In this article, we'll walk you through the steps to wire an LED dimmer, complete with a diagram for better understanding.
LED調光器の種類
Before diving into the wiring process, it's important to understand the types of LED dimmers available:
- 位相カット調光器:住宅用途に適した、最も一般的なタイプの調光器です。
- リーディングエッジおよびトレーリングエッジTRIACディマー:LED調光照明や従来の照明に適した、互換性の高いタイプの調光器です。
- 0-10V調光器:商業用や工業用でよく使用され、精密な制御が可能。
- DALI調光器: これらは通常パネルであり、DALIマスターによって制御され、インテリジェントシステムや人間中心の照明に適している。
- スマート調光器:Wi-FiまたはBluetooth対応の調光器で、スマートフォンや音声コマンドで操作できる。

一般的な調光器の配線作業
用意されたコンポーネント
- LED照明器具または電球
- LED対応調光スイッチ
- 電線(通常14または12ゲージ)
- ワイヤーナットまたはコネクター
- ドライバー
- ワイヤーストリッパー
- 電圧テスター
- オプションジャンクションボックス

安全上のご注意
- 電気工事を始める前に、必ずブレーカーで電源を切ってください。
- 電圧テスターを使って、電源がオフになっていることを確認する。
- 各地域の電気法規に従ってください。
- If you're unsure about any step, consult a qualified electrician.
ダイアグラム
+----------------+ +-------------------+
| | | |
| LED調光器 |------| LEDドライバ
+----------------+ +-------------------+
|
| |
| LEDライト
| |
+----------------+
簡単な共通ステップガイド
ステップ1:電源を切る
サーキットブレーカーで電源を切り、電圧テスターで電源が切れていることを確認する。
ステップ2:ワイヤーの準備
ワイヤーストリッパーを使い、接続する電線の端から絶縁被覆を約半インチ剥ぎ取る。
ステップ3:ワイヤーを特定する
Typically, you'll have the following wires:
- 茶/黒:熱線
- 青/白中性線
- 緑/黄色または裸銅:アース線

ステップ4:ディマーの接続
- アース線:調光器からのアース線を電気ボックスのアース線にワイヤーナットを使って接続してください。
- ニュートラルワイヤー:調光器に中性線(通常は白)がある場合は、電気ボックスの中性線に接続してください。
- ホットワイヤー:調光器からの黒線を電気ボックスの黒(ホット)線に接続してください。
ステップ5:LEDライトの接続
- Connect the other end of the black (hot) wire to the LED light's black wire.
- Connect the other end of the white (neutral) wire to the LED light's white wire.
- Connect the other end of the ground wire to the LED light's ground wire.
ステップ6:すべての接続を保護する
ワイヤーナットまたは適切なコネクターを使用して、すべての接続を固定してください。裸線が露出しないようにしてください。
ステップ7:テスト
Turn the power back on at the circuit breaker and test the dimmer to ensure it's working as expected.
5種類の調光器の詳細ガイド
位相カット調光器
Wiring a phase-cut dimmer can be a complex task that involves working with high-voltage electrical circuits. Incorrect wiring can result in electrical shock, fire, or damage to the dimmer and other electrical components. If you're not experienced with electrical work, it's strongly recommended that you consult with or hire a qualified electrician to perform the installation.
とはいえ、もしあなたが電気工事に慣れていて、必要な安全策をすべて講じているのであれば、以下にフェーズカット調光器の配線方法に関する一般的なガイドを示します:
必要な道具と材料
- ドライバー
- ワイヤーストリッパー
- 電気テープ
- ワイヤーナット
- マルチメーター
- フェーズカット調光スイッチ
- 適切な電気ボックスとカバープレート

安全上のご注意
- Turn off the power to the circuit you'll be working on at the circuit breaker.
- マルチメーターで電源が切れていることを確認する。
- 手袋や目の保護具など、適切な安全装備を着用すること。
ステップ
- ワイヤーを特定する:電気ボックスを開け、配線を確認します。黒(ホット)線、白(ニュートラル)線、そしておそらく緑か裸銅(アース)線が見えるはずです。
- 調光器の準備: Unpack the phase-cut dimmer and read the manufacturer's instructions carefully. Identify the wires or terminals on the dimmer. Typically, you'll see similar colors: black (or red) for the hot wire, white for the neutral, and green for ground.
- 古いスイッチを外す: If you're replacing an old switch, disconnect it by unscrewing the wire nuts and separating the wires.
- 照明設備(Dimmable led の運転者)と調光器を接続して下さい: ① Connect Dimmer #4 port's wire of LED driver's INPUT -L port. ② Connect the output terminals of LED driver (LED+/LED-) to the input terminals of the light fixtures ③ Connect the dimmer's L2 to electricity L line, and LED driver's N to electricity N Line. (line with AC marked in the diagram)
- ニュートラルワイヤーを接続する:調光器にニュートラル接続が必要な場合は、電気ボックスからの白線を調光器の白線または端子に接続してください。ワイヤーナットを使用して接続を固定してください。
- ホットワイヤーを接続する:電気ボックスからの黒(ホット)線を調光器の黒(または赤)線または端子に接続します。ワイヤーナットを使用して接続を固定してください。
- タック&セキュア:すべてのワイヤーナットがしっかりと固定されていることを確認しながら、慎重にワイヤーを電気ボックスに戻します。
- ディマーの取り付け: Screw the dimmer into the electrical box, following the manufacturer's instructions.
- カバープレートの取り付け:カバープレートを調光器の上に取り付けます。
- テスト: Turn the power back on at the circuit breaker and test the dimmer to make sure it's working as expected.



Remember, this is a general guide. Always follow the manufacturer's instructions and local electrical codes. If you're unsure about any step, consult a qualified electrician.

リーディングエッジおよびトレーリングエッジTRIACディマー
リーディングエッジ調光器とトレーリングエッジ調光器は、照明の明るさを制御するために使用される位相カット調光器の一種です。リーディングエッジ調光器はACサイクルの開始位相をカットし、トレーリングエッジ調光器は終了位相をカットします。このタイプの調光器は、白熱灯、ハロゲン灯、一部のLEDやCFL照明によく使用されます。
注: Working with electrical circuits can be dangerous. If you're not experienced, it's strongly recommended to consult or hire a qualified electrician. Incorrect wiring can result in electrical shock, fire, or damage to the dimmer and other electrical components.
必要な道具と材料
- ドライバー
- ワイヤーストリッパー
- 電気テープ
- ワイヤーナット
- マルチメーター
- リーディングエッジまたはトレーリングエッジ調光スイッチ
- 電気ボックスとカバープレート
- 安全装備(手袋、保護メガネ)

安全上のご注意
- Turn off the power to the circuit you'll be working on at the circuit breaker.
- マルチメーターで電源が切れていることを確認する。
- 手袋や目の保護具など、適切な安全装備を着用すること。
一般的な配線手順
- ワイヤーを特定する: Open the electrical box and identify the wires. Typically, you'll see a black (hot) wire, a white (neutral) wire, and possibly a green or bare copper (ground) wire.
- 調光器の準備: Unpack the dimmer and read the manufacturer's instructions carefully. Identify the wires or terminals on the dimmer. You'll usually see similar colors: black (or red) for the hot wire, white for the neutral, and green for ground.
- 古いスイッチを外す: If you're replacing an old switch, disconnect it by unscrewing the wire nuts and separating the wires.
- 照明設備(Dimmable led の運転者)と調光器を接続して下さい: ① Connect Dimmer OUTPUT (AC100-240V) wires of LED driver's AC input (N, L). ② Connect the output terminals of LED driver (LED+/LED-) to the input terminals of the light fixtures. ③ Connect the dimmer INPUT (AC100-240V) to electricity (line with AC marked in the diagram)
- ニュートラルワイヤーを接続する:調光器にニュートラル接続が必要な場合は、電気ボックスからの白線を調光器の白線または端子に接続してください。ワイヤーナットを使用して接続を固定してください。
- ホットワイヤーを接続する:電気ボックスからの黒(ホット)線を調光器の黒(または赤)線または端子に接続します。ワイヤーナットを使用して接続を固定してください。
- タック&セキュア:すべてのワイヤーナットがしっかりと固定されていることを確認しながら、慎重にワイヤーを電気ボックスに戻します。
- ディマーの取り付け: Screw the dimmer into the electrical box, following the manufacturer's instructions.
- カバープレートの取り付け:カバープレートを調光器の上に取り付けます。
- テスト: Turn the power back on at the circuit breaker and test the dimmer to make sure it's working as expected.


その他の考慮事項
- 互換性:調光器が使用する照明の種類(LED、白熱灯、ハロゲンなど)に対応していることを確認してください。
- 負荷要件:調光器の負荷要件を確認し、制御する照明の総ワット数と一致していることを確認してください。
- マルチ・ウェイ・スイッチング: If you're installing a dimmer in a multi-way switching arrangement (e.g., 3-way switch), make sure to get a dimmer that supports this and follow the specific wiring instructions for multi-way setups.
Always follow the manufacturer's instructions and local electrical codes. If you're unsure about any step, consult a qualified electrician.
0-10V 調光器
0-10V調光制御方式は、特に商業用や工業用の照明制御アプリケーションでは標準的な方式です。この方式では、低電圧信号を用いて照明器具の調光レベルを制御します。電圧信号は、0V(消灯)から10V(全輝度)までの範囲で、その間の明るさは様々です。
基本コンポーネント:
- 0-10V調光機能付き照明器具
- 0-10Vディマーまたはコントローラー
- 低電圧制御ワイヤー(通常18-22 AWG)
- 電源(照明器具に必要なもの)
- オプション自動化システムまたはビル管理システム(BMS)

配線のステップ
- LEDドライバ:照明器具と0-10V調光器がそれぞれの電源に正しく接続されていることを確認してください。
- コントロールワイヤー:0-10V制御信号用に2本の追加ワイヤーが使用されています。1本はプラス制御信号用(+)、もう1本は制御信号グランド用(-)です。
- 照明器具への接続:DIM+"と "DIM-"などと表示されていることがよくあります。
- 調光器への接続:制御線の他端を0-10V調光器またはコントローラの対応する端子に接続します。
- 極性:コントロールワイヤーを接続する際、正しい極性を維持してください。プラス線は器具と調光器の両方の "DIM+"端子に接続し、マイナス線は "DIM-"端子に接続してください。
- オプション・オートメーション: If you are integrating the 0-10V dimming system into a larger automation or BMS, ensure that the control wires are properly connected to the system's interface.
- テスト:すべての接続が完了したら、システムの電源を入れ、調光機能が期待通りに動作するかテストしてください。

安全上の注意
- 電気配線の作業をする前には、必ず電源を切ってください。
- ワイヤーナットまたは適切なコネクターを使用して、すべての接続を固定します。
- 各地域の電気に関する法令に従ってください。
- 不明な点がある場合は、資格のある電気技術者に相談してください。
0-10V調光システムはその信頼性の高さで知られ、商業ビルや産業環境、そして最近では高度な照明制御システムを備えたスマートホームなど、光量の精密な制御を必要とする用途で広く使用されています。
DALI調光器
DALI(Digital Addressable Lighting Interface)は、建築物の照明を制御するためのプロトコルで、そのシンプルさと堅牢さで知られています。DALI調光器は、DALI対応の照明器具を制御するために使用されます。従来の調光器とは異なり、DALI調光器は照明器具とデジタル通信を行うため、より精密な制御が可能で、グルーピングやシーン設定などの追加機能も備えています。
安全上のご注意
- Always turn off the power to the circuit you'll be working on at the circuit breaker.
- マルチメーターで電源が切れていることを確認する。
- 手袋や目の保護具など、適切な安全装備を着用すること。
- If you're not experienced with electrical work, consult or hire a qualified electrician.
必要な道具と材料
- ドライバー
- ワイヤーストリッパー
- 電気テープまたは熱収縮チューブ
- ワイヤーナットまたは適切なコネクター
- マルチメーター
- DALI調光器
- DALI対応照明器具
- DALIコントロールケーブル(通常2線式、極性フリー)
DALI調光器の一般的な配線手順
- マニュアルを読む:作業を始める前に、DALI調光器とDALI対応照明器具の両方の設置マニュアルを読み、特定の要件と機能を理解してください。
- ネットワークの計画:DALIネットワークは通常デイジーチェーントポロジーで配線されますが、スターやツリートポロジーも可能です。それに応じてネットワークのレイアウトを計画してください。
- 電源を切る: Make sure to turn off all power to the circuits you'll be working on.
- ディマーへの電源配線: Connect the power supply wires to the DALI dimmer according to the manufacturer's instructions. This usually involves connecting a live (hot), neutral, and possibly a ground wire.
- DALIラインの接続: DALI uses a separate 2-wire control line for communication. Connect the DALI control wires from the dimmer to the DALI-compatible lighting fixtures. DALI is generally polarity-free, meaning you don't have to worry about connecting the wires backward.
- デイジーチェーンまたはスター構成: Depending on your layout plan, connect the DALI control wires to each fixture in a daisy-chain or star configuration. If you're using a daisy-chain, the DALI lines will go from the dimmer to the first fixture, then from the first fixture to the second, and so on.
- 住所:DALIシステムによっては、照明器具ごとにアドレスを設定する必要があります。これは通常、別のDALIコントローラーまたはメーカーが提供するソフトウェアを使用して行うことができます。
- 接続のテスト:電源を回復する前に、すべての接続が安全であることを再確認してください。
- 電源の回復とテスト:電源を入れ直し、システムをテストして、調光器が期待通りに照明器具を制御できることを確認してください。
- シーンまたはグループの設定: If your DALI system supports advanced features like scene setting or grouping fixtures, you can configure these settings according to the manufacturer's instructions.

Remember, DALI systems can vary significantly in their features and requirements, so always refer to the manufacturer's documentation for the most accurate and detailed information.
スマート調光器

スマート調光スイッチの配線は、従来の調光器の配線と同様の手順を踏みますが、スマートホームネットワークにデバイスを接続するための考慮事項がいくつか追加されます。スマート調光器は、スマートフォンアプリ、音声コマンド、オートメーションルーチンを使って制御することができ、多くの場合、ワイヤレス接続を維持するために、常時給電用のニュートラルワイヤーを必要とします。
注: Working with electrical circuits can be dangerous. If you're not experienced, it's strongly recommended to consult or hire a qualified electrician. Incorrect wiring can result in electrical shock, fire, or damage to the dimmer and other electrical components.
必要な道具と材料
- ドライバー
- ワイヤーストリッパー
- 電気テープ
- ワイヤーナット
- マルチメーター
- スマート調光スイッチ
- 電気ボックスとカバープレート
- 安全装備(手袋、保護メガネ)
安全上のご注意
- Turn off the power to the circuit you'll be working on at the circuit breaker.
- マルチメーターで電源が切れていることを確認する。
- 手袋や目の保護具など、適切な安全装備を着用すること。
一般的な配線手順
- マニュアルを読む:スマート調光器を使用する前に、スマート調光器の設置マニュアルをよく読み、スマート調光器特有の要件や機能を理解してください。
- ワイヤーを特定する: Open the electrical box and identify the wires. Typically, you'll see a black (hot) wire, a white (neutral) wire, and possibly a green or bare copper (ground) wire.
- 調光器の準備: Unpack the smart dimmer and identify the wires or terminals. You'll usually see similar colors: black (or red) for the hot wire, white for the neutral, and green for ground.
- 古いスイッチを外す: If you're replacing an old switch, disconnect it by unscrewing the wire nuts and separating the wires.
- アース線の接続:電気ボックスからアース線を調光器のアース線または端子に接続してください。ワイヤーナットを使用して接続を固定してください。
- ニュートラルワイヤーを接続する:ほとんどのスマート調光器は、常時電源を供給するためにニュートラル接続が必要です。ボックスからの白線を調光器の白線または端子に接続します。接続はワイヤーナットで固定してください。
- ホットワイヤーを接続する:電気ボックスからの黒(ホット)線を調光器の黒(または赤)線または端子に接続します。ワイヤーナットを使用して接続を固定してください。
- タック&セキュア:すべてのワイヤーナットがしっかりと固定されていることを確認しながら、慎重にワイヤーを電気ボックスに戻します。
- ディマーの取り付け: Screw the smart dimmer into the electrical box, following the manufacturer's instructions.
- カバープレートの取り付け:カバープレートを調光器の上に取り付けます。
- 電源の回復とテスト: Turn the power back on at the circuit breaker and test the dimmer to make sure it's working as expected.
スマート機能の追加ステップ
- Wi-Fiに接続する: Follow the manufacturer's instructions to connect the smart dimmer to your Wi-Fi network, usually via a smartphone app.
- ソフトウェア・アップデート:スマート調光器によっては、設置後にソフトウェアのアップデートが必要な場合があります。これは通常アプリから行います。
- 設定を構成する:アプリを使って、スケジュール、シーンなどの設定や、Amazon AlexaやGoogle Assistantなどのスマートアシスタントによる音声コントロールが可能。
- テスト・スマート機能: Test the smart features to ensure they're working as expected.
Always follow the manufacturer's instructions and local electrical codes. If you're unsure about any step, consult a qualified electrician.
結論
Wiring an LED dimmer is a straightforward process if you follow the steps carefully and take necessary safety precautions. Whether you're looking to enhance your home's ambiance or improve energy efficiency in a commercial setting, an LED dimmer is a valuable addition to your lighting system.